[TriLUG] Linksys WPC11 (wireless PC Card)
Robert Baker
rbaker at smithlaw.com
Tue Oct 29 13:55:10 EST 2002
Jeremy,
/var/log/messages shows this line:
Oct 29 13:15:59 localhost kernel: wvlan_cs: Unrecognised card, card return
vendor = 0x0000, please report...
I see this during boot up also
Orinco_cs is not loaded (lsmod)
Iwconfig:
lo no wireless extensions.
eth0 IEEE 802.11-DS ESSID:"non-spec" Nickname:"Prism I"
Mode:Managed Frequency:2.422GHz Access Point: 44:44:44:44:44:44
Bit Rate:2Mb/s Tx-Power=15 dBm Sensitivity:1/3
RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0/92 Signal level:-102 dBm Noise level:-102 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Hope this helps
>>> Rob Baker <<<
Webcentric Applications Developer
-----Original Message-----
From: Jeremy Portzer [mailto:jeremyp at pobox.com]
Sent: Tuesday, October 29, 2002 1:32 PM
To: trilug at trilug.org
Subject: RE: [TriLUG] Linksys WPC11 (wireless PC Card)
I'm not sure that's actually a problem, although I would have expected it to
show up as "PrismII" instead of Lucent/Agere/Melco, but whatever.
As long as it's actually using the orinoco_cs driver, it doesn't really
matter what the config tool thinks it is. Look at /var/log/messages and
also type "lsmod" at a shell prompt... does orinoco_cs get loaded
properly? If you type "iwconfig" at a shell prompt, do you get a bunch
of stats about your wireless card, or an error?
Now, as far as the card timing out when activated, have you set up the
TCP/IP configuration yet? If you leave everything at the defaults, it will
attempt to connect to a DHCP server. Do you have a wireless network and a
DHCP server? Is the ESSID (and WEP, if applicable) configured correctly?
If you haven't yet set up the DHCP server or other appropriate TCP/IP
settings, the card timing out when activated is the expected behavior.
--Jeremy
On Tue, 2002-10-29 at 13:21, Robert Baker wrote:
> Jeremy,
>
> Now when I go into Network Configuration RH8 sees the card as a
> "Lucent/Agere/Melco PCMCIA..." It's 'Inactive' and when I try to
> activate the card is times out with an error.
>
> I've tried to go in and add a new adapter (Network Configuration >
> Hardware) but do not see the Linksys listed and no where to add it.
>
> I'm not sure what to do next--most of the devices listed in
> /etc/pcmcia/config are not listed in the GUI dropdown.
>
> Any suggestions?
>
>
>
>
>
> >>> Rob Baker <<<
> Webcentric Applications Developer
>
> -----Original Message-----
> From: Robert Baker [mailto:rbaker at smithlaw.com]
> Sent: Monday, October 28, 2002 4:32 PM
> To: 'trilug at trilug.org'
> Subject: [TriLUG] Linksys WPC11 (wireless PC Card)
>
>
> Jeremy,
>
> I added the following lines to /etc/pcmcia/config:
>
> card "Linksys Instant Wireless Network PC Card WPC11 v3"
> manfid 0x0274, 0x1613
> bind "orinoco_cs"
>
> Thanks again for showing me the way...
>
> I left the actual card at home so I can't test at work (no access here
> anyway).
>
> Where would I configure the card (security etc...) once RH8 recognizes
> it?
>
>
>
> <> Rob Baker <>
> Webcentric Applications Developer
> Smith, Anderson, Blount, Dorsett, Mitchell, Jernigan, L.L.P.
> 2500 First Union Capitol Center (Box 2611)
> Raleigh, NC 27602-2611
> v. 919-838-2010 <> f. 919-821-6800
> www.smithlaw.com
>
>
_______________________________________________
TriLUG mailing list
http://www.trilug.org/mailman/listinfo/trilug
TriLUG Organizational FAQ:
http://www.trilug.org/~lovelace/faq/TriLUG-faq.html
More information about the TriLUG
mailing list